When you initiate a Print / Snapshot / Auto Measuring / Calibration operation in eufyMake Studio, you may see the prompt "Device is Busy", which prevents the operation from continuing.
This usually means the device is not currently in an Idle (ready) state. Instead, it is either performing another process or is in a condition that must be completed or resolved first. This article will help you understand what the device may be doing, which situations will block operations, and how to return the device to a printable state.
The prompt will appear whenever the device is in a non-Idle state. You can check the exact status on the Device Page, where more detailed information about the current operation is displayed.
Before printing begins, the device completes several preparation steps:
Taking snapshots (capturing the print area for positioning)
Auto measuring (rotary object dimensions and position)
Height measuring (material thickness)
Transmitting the file (uploading/downloading)
Ready to print (waiting for user confirmation)
During any of these stages, the device is considered busy, and new operations cannot be started.
When the device is actively printing, all other operations are blocked. This includes:
Printing in progress
Pre-print priming (printhead preparation)
If printing is paused:
It may be paused manually or due to a recoverable issue (e.g. low ink)
The device remains busy until you resume or end the current task
To maintain printhead performance, the device may run maintenance operations such as:
Flash Clean / Medium Clean / Deep Clean
Ink injection
Automatic maintenance (auto clean, auto deep clean, auto moisturizing)
The device remains busy throughout these processes. You must wait for them to complete before printing or calibrating.
After deep cleaning or moisturizing, the printhead remains in a soaking state.
In this condition:
The device will not allow printing or calibration
You must complete Inject Ink before continuing
You may see prompts such as:
"The printhead remains in deep cleaning state. Please inject ink before printing."
"The printhead remains in moisturizing state. Please inject ink before printing."
If a maintenance task is interrupted, the device may display:
Maintenance Paused
A prompt to tap Continue
To avoid affecting future prints, you should complete the maintenance task first. Once finished, the device returns to a normal state.
The device may be performing calibration tasks, such as:
Self-check
Camera calibration
Zero-point calibration
These processes require exclusive control of the device, so no other operations can be started until they are complete.
After first setup or a factory reset, the device must complete initialization in the App. During this process, printing and calibration are not available.
The device may be:
Downloading firmware
Installing firmware
During this time:
All operations are disabled
Power and network must not be interrupted
During a factory reset:
The process takes approximately 10 minutes
The device will restart automatically
All operations are unavailable until the reset is complete.
These states also prevent operations:
Offline:
Device is powered off or disconnected from the network
Unavailable:
Caused by consumable issues (e.g. empty ink) or system faults
Usually accompanied by an error code and instructions
You must resolve the issue shown on the Device Page before continuing.
| Device Status | Snapshot | Auto Measure | Calibrate | |
| Idle | ✅ | ✅ | ✅ | ✅ |
| Power Saving Mode | ✅ | ✅ | ✅ | ✅ |
| Preparing to Print | ❌ | ❌ | ❌ | ❌ |
| Printing | ❌ | ❌ | ❌ | ❌ |
| Printing Paused | ❌ | ❌ | ❌ | ❌ |
| Performing Maintenance | ❌ | ❌ | ❌ | ❌ |
| Maintenance Status | ❌ | ❌ | ❌ | ❌ |
| Maintenance Paused | ❌ | ❌ | ❌ | ❌ |
| Calibrating | ❌ | ❌ | ❌ | ❌ |
| Initializing | ❌ | ❌ | ❌ | ❌ |
| Firmware Updating | ❌ | ❌ | ❌ | ❌ |
| Factory Resetting | ❌ | ❌ | ❌ | ❌ |
| Offline | ❌ | ❌ | ❌ | ❌ |
| Unavailable | ❌ | ❌ | ❌ | ❌ |
When "Device is Busy" appears:
Go to the Device Page and check:
Main status (e.g. Printing, Maintenance, Calibrating)
Sub-status (e.g. snapshot, file transfer, firmware update)
Progress bar and available actions (Cancel / Continue / Inject Ink)
Take action based on what you see:
If a task is running → wait for completion
If input is required → follow the prompt (Continue / Inject Ink / Retry)
Once complete, the device returns to Idle, and you can start your operation again.
If the device does not return to Idle:
Check whether it is stuck on a status with no progress
Look for prompts requiring action (Maintenance Paused / Initialization / Unavailable)
Check for network issues and refresh the Device Page if needed
If the issue persists, contact eufyMake Customer Support and provide: